当前位置:首页 » 新型汽车 » 电动汽车配置英文版

电动汽车配置英文版

发布时间: 2021-09-05 17:38:31

A. 纯电动汽车和混合动力车概括为什么英文名称是

1.纯电动汽车:Blade Electric Vehicles。
2.混合动力车:Hybrid Electrical Vehicle。

1.纯电动汽车(Blade Electric Vehicles ,简称BEV),即是一种采用单一蓄电池作为储能动力源的汽车。它利用蓄电池作为储能动力源,通过电池向电机提供电能,驱动电动机运转,从而推动汽车前进。从外形上看,电动汽车与日常见到的汽车并没有什么区别,区别主要在于动力源及其驱动系统。即纯电动汽车的电动机相当于传统汽车的发动机,蓄电池相当于原来的油箱。
2.混合动力汽车(Hybrid Electrical Vehicle,简称HEV) 是指同时装备两种动力来源——热动力源(由传统的汽油机或者柴油机产生)与电动力源(电池与电动机)的汽车。通过在混合动力汽车上使用电机,使得动力系统可以按照整车的实际运行工况要求灵活调控,而发动机保持在综合性能最佳的区域内工作,从而降低油耗与排放。

B. 哪里可以下载电动汽车类中英文论文

用BAIDU用惯了?去www.google.com去找找啊!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

C. 高分悬赏英文版的电动车的说明书。急用!!

中文和英文版本。字数限制,只写了英文!

First, electric car use environmental condition

Electric car when exwork uses by an examination.

(1) main technical performance request

(1) electric car highest speed should not be bigger than 20km/h.

(2) electric car entire vehicle quality should not be bigger than 40kg.

(3) electric car must have the good foot pedal to ride the good function.

After a (4) electrically operated bicycle charge continues the course to be supposed not to be smaller than 25km.

(5) electrically operated bicycle makes the electrically operated uniform speed rides when the line the noise by the maximum speed to be supposed not to be bigger than 62db.

(6) hundred kilometers electricity consume should not be bigger than 1.2kwh.

(7) electrically operated bicycle electric motor fixed continuously output should not be bigger than 240W.

(2) entire vehicle safety requirements

(1) the maximum speed electric bicycles to electric ride, the dry braking distance should be not more than 4m, wet braking distance should be not more than 15m.

(2) electric bicycle tire wheel width should be not more than 54mm. Frame / Front * combination of the impact / shock strength of the riser, the horizontal tubes, wheels, saddle, pedal should be in accordance with the provisions of GB3565-1993.

(3) electric cars should be equipped with a headlight and reflector before and after reflector, side reflector, should be returned to its port after device installed.

(4) the installation of electrical systems in place, the correct polarity, the system of electrical installations should comply with the requirements of GB3565-1993. Current electrical wiring should be adapted to ensure that electrical safety can * ride.

(5) of the electrical system to take water-resistant measures, the system should not be used for exposed wiring, and electrical parts of the body shell should not be charged, the insulation resistance value should be not less than 2MΩ.

(6) of the battery electric bicycle should be a good seal. Under normal conditions, the installation location, charge, discharge, when there should be no leakage of fluid phenomena. The nominal battery voltage should be not more than 48V.

(7) electric bicycle brake power devices should be in the brake should be able to automatically cut off the power first.

(8) electric bicycle controller should have the under-voltage, over-current protection function and short-circuit device. Riding in the electric, the speed should be stable.

(C) vehicle assembly requirements

(1) electric bike models require assembly should not be installed the wrong equipment and leakage.

(2) electric bicycle fastening the fasteners should be in place, the rotating parts should be flexible operation.

(3) of the symmetric components in the frame center should be symmetrical face can not be significantly skewed.

(4) variable-speed devices and the braking system should be fitted correctly, flexible manipulation.

(5) Electric Bicycle Fixed pieces of moving parts and does not allow grazing.

(6) radial rim, beating the volume of a round face, with a rim前后轮*, frame-ping, Li * on both sides of space relative deviation, relative deviation前后轮center surface are consistent with the provisions of GB/T3566-1993.

(D) the appearance of vehicle requirements

(1) Electric Bicycle parts of the exposed surface should be clean, no dirt, no rust, trademarks, decals should be complete, clear, correct position.

(2) electric vehicle plastic parts of the color of the surface should be uniform, non-obvious edge, scratch, crack and sag.

(3) of the plating over the exposed parts in line with the provisions of QB/T1217-1991.

(4) over the exposed parts of the paint in line with the provisions of QB/T1218-1991.

(5) pieces of aluminum alloy exposed in line with the provisions of QB/T1284-1995.

(E) electric vehicle is subject to 100km cycling road test

During the trial process can not occur in all parts of the broken vehicle and electrical control system is damaged or invalid parts. Cycling can not afford to lose its electrical function.

(Vi) electric cars must be manual and have the following

(1) read the manual carefully to understand the performance of electric bike before, do not use electric bicycles, not to lend will not manipulate people riding electric bike.

(2) of the horizontal tubes, the risers, saddles, saddle tube and wheel torque fasteners should be tightened Recommended: should be noted that the riser pipe and the saddle of the safety line.

(3) parts lubrication, lubrication oil lubrication cycle and recommended.

(4) right up the chain tight and adjustment method.

(5) the adjustment of brakes and brake Paper on the proposed change, pay attention to rain, snow riding should increase the braking distance.

(6) electric motors, controllers, batteries and maintenance of the correct method to use.

(7) the correct charger, the safe use of the method.

(8) GB/17761-1999 standards in Appendix A (the standard in Appendix) the technical parameters and performance indicators.

Second, the use of electric cars Notes

(A) must comply with operating requirements for electric bikes.

(B) the design standards of electric vehicles for load 75kg, over 90kg when the load, the battery and motor will be damaged.

(C) a long time the battery can not be shelved, shelved charge at least once a month. After cycling the battery discharge must be kept fully charged, it will be a great impact on battery life, will cause serious end-of-life battery.

(D) When the power is exhausted, the system will automatically power off. However, after power off, battery and counter-dancing's "virtual" voltage (reactive power and voltage), then must be recharged after use, otherwise it will create over discharge the battery, which will damage the battery can not be repaired.

(E) electric bicycle trip mileage continued 40-50km. The actual trip mileage continued use will be affected by many factors (such as frequent brake, start, road surfaces, the temperature is too low, on steep slopes, wind speed and under-inflated tires, heavy load) the impact.

(F) attention to the front of the display instrument. Power to open, the electric vehicle can ride at a state, a red LED power indicator light, while green, yellow LED power indicator light, with power cycling, when the green light, yellow light is off, that is about to run out of battery power, at the moment electric ride should stop as soon as possible to the battery charge.

(Vii) pre-riding all the preparatory work must be ready to ensure ride safety.

(1) get off the ground, sliding on and off is prohibited in order to ensure the safety of users.

(2) on the car before opening the power lock switch, and get off before the power lock-off switch.

(3) adjusting the saddle and handlebar height, saddle attention may not be exposed riser pipe and the safety line.

(4) should be slow to speed up cycling. From 0-20km / h, acceleration time is not less than 10S, in order to maintain smooth traffic.

(5) to minimize the number of start. Rapid economic growth of the car (the most power to speed) is generally 16-18km / h.

(6) attention to the braking distance when the ride is generally 4m, the rain increased to double the braking distance.

(H) the horizontal pipe, the riser of the tightened torque for the 16-18N.m.

(I) saddle, saddle tightened torque tube fasteners for the 18-20N.m.

(J) torque for fastening the rear 40-45N.m; front fastening torque for the 18-20N.m.

(K) before the gate skin wheel should be parallel surface pressure, the level of consistency. Paper gates of the space and the wheel is not more than 3mm; brake tightness to grip the handle away from the gate to be able to check the appropriate 10mm. Not the brake, the brake and the skin may not be any part of the wheel contact, gate Paper obvious wear and tear should be replaced in time to avoid injury Rim.

(12) should be elastic spokes, chains grazing may not occur with the body. Adjustment, adjustable rear and the central axis of the distance from the chain up tight control in the 10-15mm.

(Xiii) the prohibition of lubricating rear.

(Xiv) to the appropriate tire pressure, caused by excessive deformation of aluminum circles; low crack caused by tire and inner tube bite; so that inner tube leakage.

(15) in charge should pay attention to:

(1) First, insert the battery charger output of the charging socket and then connect the power input AC 220V.

(2) red charging indicator light on the charger that the normal charge. Fully charged before the green indicator light, green light and then 1-3 hours for the best filling.

(3) finished first unplug the charger's AC power plug, then unplug and plug the battery connections.

(4) does not prohibit the charging, the time will be empty charger connected to the AC power on.

(5) can take to recharge the battery box can also be recharged in the vehicle directly.

(6) If the box had to recharge the battery, charge the battery box back into the end, we have to lock up, the battery box to prevent power outages caused by the phenomenon of loosening.

(7) directly in the vehicle when charging is prohibited to open the power supply electric bicycle lock, to prevent burning charger.

(8) charging the surrounding environment should be ventilation, no fire, be sure to use consistent with the configuration of the charger, the demolition of the battery box is strictly prohibited without permission.

(9) charger work on a child to reach in order to avoid the risk.

(10) light using light to avoid shock release.

(16) years and as far as possible to prevent the motor started, riding the best first human motor starting up again so as to avoid a zero start, the impact of too much current the battery, electrical and machinery life.

(17) should ride on rainy days to prevent the controller and motor in water, caused by short circuit damage.

(18) climbing, on the bridge, the wind speed and great battery-powered flow through the impact of motor and battery life, the best human-assisted riding at this time.

Third, the electric bicycle maintenance

(A) the maintenance of electrical and maintenance

(1) vehicle is sold prior to installation and commissioning to the best state, in use, please do not arbitrarily removable appliances and related components. Found that when riding transmission components such as the issue of abnormal sound, electricity and other unusual circumstances do not work, should be invited to professional maintenance repair division.

(2) motor are not required to adjust the normal use or maintenance, just some clean work surface to st. Not to add components in the transmission oil.

(B) the maintenance of batteries and maintenance

(1) When the instrument panel red LED lights when the voltage that power into the hunger zone, should be charging. Charge will be timely to extend the battery life greatly. A day on the battery is fully charged, each charging time should be 8-12 hours. At any time to allow the battery to maintain state of abundance, of great benefit to their life. If after riding a timely charge, will be a great impact on battery life. May result in severe end-of-life battery.

(2) electric bike starts, should be slow to accelerate; in a larger gradient of the road and moving against the wind, it is best able to push enough support to avoid high-current discharge batteries to extend battery and motor life. Electrical components and to avoid burnout.

(3) long-term battery when not in use should be kept fully charged, and be not less than every three months to conct a supplementary 24-hour charge.

(4) Rechargeable batteries should be in circulation in the air environment. * To avoid a nearby fire source, rechargeable battery pack when it would be preferable to remove in order to facilitate heat dissipation.

(5) batteries in the best working environment temperature

15 ℃ -40 ℃. In this temperature range, the battery will have an impact on the normal work.

(6) can not short-circuit the battery positive and negative side to avoid danger.

(7) can only use the manufacturers provide a dedicated charger for charging.

(8) battery is a special battery. Please do not as a power source other than electric bicycle use, so as to avoid battery damage.

(9) can not use organic solvents to clean the battery case. Accidents involving fires, fire can not use carbon dioxide, and carbon tetrachloride should be used like a fire extinguisher.

(10) with group electrical failure if, please sent to manufacturers or authorized and properly handle relevant agencies. Please do not arbitrarily discarded in order to avoid environmental pollution.

(11) ambient temperature higher than 40 ℃ or lower than -10 ℃, the battery life will be shortened. So when the summer heat, the battery should avoid direct sun. Low temperature in winter, the batteries should be stored indoors, and indoors for recharging. Battery fully charged, the charge should be extended for a further 2 hours.

(12) ambient temperature at -10 ℃, the battery can only proce 60% of electricity consumption. Therefore, the full power of winter mileage than a summer full of power to rece a lot of mileage. Winter driving in the electric power when traveling for a good pedal.

(13) battery is a consumable, battery life is limited. Battery end-of-life period should be based on mileage full power can only be achieved once the state (25Km) for assessment of the half. That is, a fully charged mileage at less than 13Km termination of battery life, batteries should be replaced with new ones.

(14) summer electric vehicles will be prohibited on a long time exposure under the scorching sun.

(C) the maintenance and maintenance controllers

Controller in the electric bike has been factory adjusted to the best condition. If riding when an electrical malfunction or loss of control over the phenomenon of non-professional maintenance personnel can only be on the cable, connector inspection, if the fault can not be ruled out immediately and professional maintenance of contact points, or manufacturers.

D. 纯电动汽车和混合动力车概括英文名称是什么

1.纯电动汽车:Blade Electric Vehicles。

2.混合动力车:Hybrid Electrical Vehicle。

E. 急急。关于电动汽车的一份英文商业计划

Electric Vehicle "propellant agents" - that is, for the construction of power stations

As we all know, in recent years electric bicycles, electric motorcycle (behind as electric cars) are quietly entered our lives, with the structure, riding, such as the appearance of continuous improvement and perfection of technology, consumer acceptance has been Has greatly improved, is graally becoming urban and township residents in one of the major means of transport. As oil prices continue to rise and there is no regulations, no Rush, and paid, seized the existence of such factors has become even more accelerated the rapid development of the electric car history.

Let us look at the back of electric vehicles is not so optimistic, 'it' from Blur, of this world have come to the Spring and Autumn dozens of spring and autumn why can not promote it » Why can not the "electric vehicle" as the wider use of this » Because "it is" the hidden behind a better person to the inherent "flaws", compared with the 'electric car' is only a short distance in the power of the simple means of transport modes of transport, electric vehicles do not like, first of all to consider three Aspects:

1, the occupants of (referring to operability, speed)

2, comfort (referring to the main structure and automotive air-conditioning system)

3, convenience (referring to whether cross-regional excursion and the rability of the battery), in which the most important factor is that we are well-known vehicle batteries, because "inherent weaknesses" and other factors will limit the electric vehicles only at close range Within a Zhuanzhuan.

We are eager to affordable high-capacity battery, but only desire is desire, some friends may think of solar energy, solar energy, lithium, the last stage of fuel cell and the use of the Shin-air battery can apply to electric To which car, where we can no doubt be said, why have not more than another way to promote it » We were to do with analysis, solar energy and solar energy is a conditional energy, only under conditions of adequate light electric vehicles can receive adequate power, if the adoption of a "hybrid force" will lose the original meaning of electric vehicles, And solar energy, solar energy in construction costs, maintenance, appearance and so on without Jinren Italy, and therefore have not been widely promoting the use of only remain in the "trial of" stage, lithium batteries, and so efficient in the performance is far more than the widely used 'Lead-acid batteries,' but the price is too high (an ordinary lead-acid batteries from 2 to 3 times), although a more satisfactory performance, but was not accepted by the public.

Second thought, even inexpensive, high-performance batteries were successfully developed, in the actual sense only to an electric vehicle in the road additional traffic on the road for a distance of energy will continue to the end, then if To find you in the middle of power, and spend a few hours or even longer time to wait for a certain comparison is a painful thing.

The electric car instry terms, the emergence of high-performance batteries are important, to achieve inter-regional long-distance electric car up and running, only by virtue of one or more efficient battery is not enough, and only through a sound professional service organizations and their Tends to be a perfect combination, the electric vehicle instry on the road ahead is possible to flourish.

Speaking here to give you an example we can clearly see the "professional services" of the importance of speaking Take fuel cars! In the 1990s, China's gasoline vehicles and fuel for more than 70 # leaded petrol, entered the 21st century has graally # 85, # 90, # 93, # 97 unleaded petrol and ethanol gasoline today, "them" The emergence and change only the burning of waste row and made a raise standards and improve the car travelling distance and convenience little effect on this factor depends primarily on the creation by the middle of the petrol filling station, it is envisaged, if not these Gas stations to provide you with convenient, then drive a car with the convenience of fun will be gone, the car's development will also be restricted.

The same token, the development of electric vehicles and to promote, whether it is ordinary lead-acid batteries, lithium or other more high-performance batteries, 'they' is the application of improved performance, the major constraints is the lack of a "professional way of Service links "is the title of the article referred to the" power station for, " 'it' will be paid to the emergence of electric vehicles and electric transport their second" life "so that the electric vehicles entered our life, and take Into the tens of thousands of households possible.

"Power Station for" the beginning of this vision to see a friend speaking, may still relatively dim, in this I hope you can read this article, I believe you must have this vision of a new understanding And recognition.

"Power Station for" As the name suggests, is one that provides road transport for the electric battery power to replace the half-way "professional services", 'it' the birth will be able to cross-regional electric vehicles travelling on the important ongoing support, below the past few Each of the key issues discussed:

I, for the construction of power plants to electric cars to what »

1, to resolve the cross-regional electric vehicles up and running and half-way energy supplies for too long, and so on. Can set up more group-level counter-charge for electric equipment, to provide a unified standard model for the battery, simply referred to the appropriate service charges for quick and easy access to energy supplies, electric vehicles for the realization of long-distance running and laid the foundation for protection .

2, for the electric vehicle procers and owners no longer battery and paved the way for the confusion, to the rapid development of electric vehicle instry has laid a possibility. Is now widely used lead-acid battery rability of "life" is not satisfactory, usually around 1.5 years -2 to replacement with a factory approved life vary greatly (pre-approved high-quality lead-acid battery life is generally three to five years) This was mainly in the actual users in the use of the various factors caused by improper, each replacement needs a lot of expenditure and expenditure on fuel similar. Solution: ① through the power station for the construction and use of cars in the purchase of the vehicle at the same time just bought a one-time match with each other for power stations, unified standard model of the battery pack can be, just after the half-way-station to replace New batteries, batteries do not have to consider the "life" and related maintenance problems. ② from power plants for professional services for the exchange of personnel after the reunification of battery maintenance, testing, charging and paste the site, maintenance, repair, and other relevant date, time, or to contribute to the future of the reasonable and orderly exchange management services. ③ unified logo for power stations, equipped with management so as to achieve security convenient for the cross-regional electricity services to enable occupants to be a worry-free, the process for the fast.

Second, how will the operation of power stations-for-»

Mainly through the following three models to carry out the operation.

1, Independent: from electric vehicle manufacturers to autonomous operation, auto sales can be taken to promote grade level by level, with car sales outlets and a rational distribution, manufacturers paid or equipment can be unified cooperation with the profit according to different approach with Extraction, pattern of brand management, distribution and unified guide the implementation of the operation. This simple and easy, from all levels of distributors wholly-owned or co-investment Bukong decomposition in order to achieve sales of automobiles and power grids points for the reunification of the two.

The disadvantage is that the future reunification of the operation of the market negative, there is bound to repeat a variety of brand building, a sign of a kind not the same as mobile phone chargers to reach unity, so that interoperability between the restrictions, for the power station Profit greatly diminished, so will electric vehicles and power plants for the orderly development of adverse effects.

2, the cooperation of the instry: by a number of companies working together to reach a consensus, play a leading role, the establishment of trade associations, the Association published standards, and actively attract more businesses join, and members of the progressive realization of internal unity, and strive to different electric vehicles A brand-branding "for power station" operations, so that more electric vehicles to brand them to participate in, do not rebuild, over-built, thus realizing the whole instry tend to enter the reasonable and orderly development track.

Difficulties exist between enterprises is fragmented more difficult to coordinate, must be one or more large enterprises take the lead and made effective for the instry to wait and see and hope to see the advantages of cooperation and to point to all areas of mutual Step by step toward cooperation between the reunification of the road to development.

3, cooperation between officials and businessmen type: in this way can be said to be a more satisfactory way, we all know that any one thing as long as the official support for the development of the implementation of speed is very fast, such as ethanol gasoline if there is no official intervention, promotion It is more difficult, the same token I believe that as long as the social, public, economic development, useful things get official support for it will become possible.

F. 雷丁电动汽车配置

雷丁电动汽车是做研发与生产的电动汽车厂家,也是第一家做微型电动SUV和电动三厢汽车的厂家。所以,具体的不同价格的配置有点不一样。雷丁电动汽车的配置一般包括:刹车助力、转向助力,高配带电动门窗和电动门锁、空调。而且续航里程达到两百多公里。

G. 关于新能源汽车的英文介绍

this paper firstly provides the connotation of new energy automobile,and then gives us an introction of the development of the new energy automobile,and on the foregoing basis summarizes those factors that will restrict the development of the new energy automobile,and in the end proposes relevant measures for the development therein.

H. "纯电动汽车" 英文术语怎么写

如果一般地说“电动汽车”,可以说electric vehicle/car
但如果强调是“纯电动汽车”,则可以说 a hundred-percent/100% electrically powered vehicle/car

斜杠/等于“或”

I. 电动车参数及配件的英文翻译

电池:Battery

电机锁:Electric lock

最高载重:Maximum load

最高车度速:Maximum speed

最大续航里程:Biggest continue voyage course

电机:Electrical machinery

豪华转把:Luxurious crank

电子防盗版:Electron security

前后大鼓刹:Around the big drum checks

电动车分为交流电动车和直流电动车。通常说的电动车是以电池作为能量来源,通过控制器、电机等部件,将电能转化为机械能运动,以控制电流大小改变速度的车辆。

电压:36V、48V (前市场48v是主流)

电池容量: 10AHM 、12AHM (这个越大越好 简单说就是越大跑的路越远。)

(9)电动汽车配置英文版扩展阅读:

配置:电动自行车是由蓄电池、电动轮毂、控制器、充电器四大件和车体部分组成。

行走系统:前桥、后桥、减震系统、悬挂系统、桥壳、半轴、平衡块、缓冲器、轮辋、轮毂、车架总成、汽车轮胎、农用车轮胎、工程机械轮胎及其他行走系统等汽车配件

电动车的驱动方式主要有3种:一种是轮毂式驱动,一种是中置式驱动,还有一种悬挂式驱动。市场上电动自行车以轮毂驱动为主,而轮毂驱动又以后轮驱动为好,前轮驱动性能相对较差。

热点内容
富士达125摩托车价格 发布:2025-06-10 20:18:44 浏览:132
elite房车 发布:2025-06-10 20:08:51 浏览:147
北京哪里卖览众房车 发布:2025-06-10 20:04:43 浏览:327
皮卡车边距30公分对哪 发布:2025-06-10 20:00:21 浏览:687
日产奇骏2017款内饰装 发布:2025-06-10 19:57:54 浏览:103
上汽大通g10七座商务车什么价格 发布:2025-06-10 19:57:41 浏览:272
后排隔断的豪车有哪些 发布:2025-06-10 19:32:19 浏览:370
f0内饰包真皮座椅 发布:2025-06-10 19:07:54 浏览:537
肯德基的皮卡丘说什么 发布:2025-06-10 18:48:59 浏览:547
皮卡堂抱猫的服装叫什么 发布:2025-06-10 18:37:56 浏览:859